Bandido - WD Bill of Materials
The following list of materials is intended to be a general guide only.
Before ordering any materials, the text and plans should be checked for
possible options. All lumber used should be first grade free from shakes and
knots. Although Douglas-fir, spruce (Sitka), and mahogany (dark red Philippine
type or Honduras) are called out in the listing, lumber typical to the locale
and of similar types and weights may be substituted. All plywood (PW) is to be
marine (MAR) or exterior (EXT) grade. The marine-type is preferable as the
inner cores are solid and thus the panel has more structural integrity.
Douglas-fir (DF) is satisfactory with the quality of the exposed faces of the
veneer being designated by the letters "A" or "B". The
"AA" grade panels are always preferable, however, "AB"
grade is acceptable. All plywood should be a minimum of three plies. All
fastenings should be bronze or hot dipped galvanized ferrous metal. Brass
fastenings are not advised nor are the electroplated screws commonly sold in
hardware stores. All screws are to be of the flat head type intended for wood.
All nails are of the ring-type nail common to boat construction. Unless
otherwise specified, all wood-to-wood joints are to be glued with a waterproof
or highly water resistant glue such as resorcinol, epoxy, or other equivalent
type used per the manufacturer's instructions regarding temperature,
clamping requirements, curing time, and mixing method.
CHECK ALL SIZES TO THE WORK PRIOR TO CUTTING.
Abbreviations used are: Mahog = mahogany; SP = Spruce; DF = Douglas-fir;
PW=plywood; Ext=exterior; MAR=marine.
ITEM |
MATERIAL |
NO.
PCS. |
SIZE |
Bottom planking |
DF, SP or Mahog veneers or MAR PW |
750 sq. ft. |
3/16" net thickness* |
Side planking |
DF, SP or Mahog veneers or MAR PW |
560 sq. ft. |
3/16" to 1/4" net thickness* |
Raised sheer side planking |
DF MAR or Ext PW AB or better |
2 sheets |
1/2" x 4' x 8' |
Transom |
DF MAR or Ext PW AB or better |
2 sheets |
3/4" x 4' x 8' |
Rope locker bulkhead
& berth tops |
DF MAR or Ext PW AB or better |
3 sheets |
1/2" x 4' x 8' |
Other bulkheads, brackets,
stemhead knee |
DF MAR or Ext PW AB or better |
5 sheets |
3/4" x 4' x 8' |
Stringer webs |
DF MAR PW AB or better |
4 sheets |
3/4" x 4' x 8' |
Cockpit sole |
DF MAR or Ext PW AB |
2 sheets |
3/4" x 4' x 8' |
Cockpit coaming |
DF MAR or Ext PW AB |
2 sheets |
1/2" x 4' x 8' |
Sun deck |
DF MAR or Ext PW AB |
2 sheets |
3/4" x 4' x 8' |
Decking |
DF MAR PW AB or better |
5 sheets |
1/2" x 4' x 8' |
Drain troughs |
DF Ext PW AB |
1 sheets |
1/2" x 4' x 8' |
FASTENINGS:
- Screws: Flathead wood type, bronze or hot dipped
galvanized
- 1-1/4" #8 - 5 gross
- 1-1/2" #8 - 12 gross
- 2" #10 - 10 gross
- 3" #14 - 1 gross
- Nails: Ring type boat nails, bronze or Monel
- 1-1/4" - 5 pounds
- Carriage Bolts: Bronze or hot dipped galvanized
complete with nuts and washers. Check lengths to work.
- 5/16" - 30 required
*Total side planking thickness: 9/16" to 3/4"
(thinner planking desirable from a weight standpoint).
Total bottom planking thickness: 3/4".
|
Return |