Renegade Bill of Materials
The following list of materials is intended to be a general guide only.
Before ordering any materials, the text and plans should be checked for
possible options. All lumber listed as 1" stock is to be standard
"lumberyard four-quarter" material which when finished may vary to
somewhat less or slightly more than 3/4" in thickness. All widths are NET
and all lengths allow for cutting to fit. Grouping lumber and purchasing
random-random material to resaw to the required size will result in
considerable savings. All lumber used should be first grade free from shakes
and knots. Although spruce (Sitka variety), oak (white oak), and mahogany (dark
red Philippine type) are called out in the listing, lumber typical to the
locale and of similar types and weights may be substituted. All plywood (PW) is
to be marine (MAR) or exterior (EXT) grade. The marine-type is preferable as
the inner cores are solid and thus the panel has more structural integrity.
Douglas-fir (DF) is satisfactory with the quality of the exposed faces of the
veneer being designated by the letters "A" or "B". The
"AA" grade panels are always preferable, however, "AB"
grade is acceptable. All plywood should be a minimum of three plies. All
fastenings should be bronze or hot dipped galvanized ferrous metal. Brass
fastenings are not advised nor are the electroplated screws commonly sold in
hardware stores. All screws are to be of the flat head type intended for wood.
All nails are of the ring-type nail common to boat construction. Unless
otherwise specified, all wood-to-wood joints are to be glued with a waterproof
or highly water resistant glue such as plastic resin, resorcinol, epoxy, or
other equivalent type used per the manufacturer's instructions regarding
temperature, clamping requirements, curing time, and mixing method.
CHECK ALL SIZES TO THE WORK PRIOR TO CUTTING. Abbreviations used are: Mahog =
mahogany; SP=Spruce; DF = Douglas-fir; PW=plywood; Ext=exterior;
MAR=marine.
ITEM |
MATERIAL |
NO.
PCS. |
SIZE |
LUMBER: |
Frame members/
deck beams |
Mahog, Oak or Sp |
75 bd. ft. Random-random four quarters stock, with some widths
to 7".
12 bd ft of 1-1/4" (five quarters) stock for transom frames |
Keel-jetdrive version |
Mahog, Oak or SP |
1
1 |
2" x 4" x 10'
2" x 12" x 5' |
Keel-other versions |
Mahog, Oak or SP |
1 |
2" x 4" x 13' |
Chine logs |
Mahog, Oak or SP |
2 |
1-1/4" x 2-1/4" x 20' |
Sheer clamps |
Mahog, Oak or SP |
4 |
3/4" net x 1-1/2" x 22' |
Sheer clamp inner lams |
Mahog, Oak or SP |
1 |
3/4" net x 1-1/2" x 12' |
Bottom Battens |
Mahog, Oak or SP |
2
2
2
2 |
1" x 2-1/2" x 18'
1" x 2-1/2" x 17'
1" x 2-1/2" x 14'
1" x 2-1/2" x 12' |
Set-up stringers |
Mahog, DF or SP |
2 |
2" x 6" x 12'* |
Motor stringers uprights
(inb) |
Mahog, DF or Oak |
2 |
2" x 4" x 2'* |
Motor stringer blocking
(inb) |
Mahog, DF or Oak |
1 |
2" x 2" x 10'* |
Motor well beam
(outboards) |
Mahog, DF or Oak |
1 |
2" x 4" x 3' |
Motor well side
uprights (outbd) |
Mahog, DF or Oak |
2 |
2" x 2" x 2' |
Decking strongback |
Mahog, Oak or SP |
1 |
1" x 2" x 10' |
Deck battens |
Mahog, Oak or SP |
2
2 |
1" x 2" x 9'
1" x 2" x 8' |
Carling |
Mahog, Oak or SP |
2 |
1" x 6" x 15' |
Coaming |
Mahog |
2 |
1" x 7" x 15' |
Filler blocking |
Mahog, Oak or SP |
2 |
1" x 2" x 8' |
Lift strakes |
Mahog |
2
2 |
1" x 3" x 14'
1" x 3" x 12' |
*Designates standard lumberyard size in both width and
thickness. |
PLYWOOD: |
Side planking |
DF Mar AB or AA |
2
2 |
3/8" x 4' x 10'**
3/8" x 4' x 12'** |
Bottom planking |
DF Mar AB or AA |
2
4 |
1/2" x 4' x 8'
1/4" x 4' x 12'** |
Decking & butt blocks |
DF Ext AB or Mahog PW |
4 |
3/8" x 4' x 8' |
Inner keel
laminations & motor
stringer laminations |
DF Ext AB |
1 |
3/8" x 4' x 8' |
Gussets |
DF Ext AB |
1 |
1/4" x 4' x 4' |
Transom, floor timbers
& transom knee |
DF Ext AB |
1 |
3/4" x 4' x 8' |
Stem &
breasthook lams |
DF Ext AB |
1 |
3/4" x 4' x 8' |
Cockpit sole & bottom
planking butt blocks |
DF Ext AC |
1 |
1/2" x 4' x 8' |
Motor well structure
(outbds) |
DF Ext AB |
2 |
1/2" x 4' x 8' |
Motor well bulkhead
(outbds) |
DF Ext AB |
1 |
3/8" x 2' x 8' |
**4' x 8' sheets can be substituted for longer sheets
in all cases. Adjust quantities accordingly. |
FASTENINGS:
Screws: Flathead wood type, bronze or hot dipped galvanized
- 3/4" #8 - 1 gross
- 1" #8 - 8 gross
- 1-1/4" #8 - 6 gross
- 1-1/2" #8 - 3 gross
- 2" #10 - 1 gross
- 3" #14 - 6 dozen
Nails: Ring type boat nails, bronze or Monel
- 1" - 2 pounds
- 1-1/4" - 1 pound
Glue: Epoxy - 1 gallon
|
Return
|