Centerfold Bill of Materials
The following list of materials is intended to be a general guide only.
Before ordering any materials, the text and plans should be checked for
possible options. All lumber listed as 1" stock is to be standard
"lumberyard four quarter" material which when finished may vary to
somewhat less or slightly more than 3/4" in thickness. All widths are NET
and all lengths allow for cutting to fit. Grouping lumber and purchasing
random-random material to resaw to the required size will result in
considerable savings. All lumber used should be first grade free from shakes
and knots. Although spruce (Sitka variety) and mahogany (dark red Philippine
type) are called out in the listing, lumber typical to the locale and of
similar types and weights may be substituted. All plywood (PW) is to be a
marine or exterior (EXT) grade. The marine type is preferable as the inner
cores are solid and thus the panel has more structural integrity. Douglas fir
(DF) is satisfactory with the quality of the exposed faces of the veneer being
designated by the letters A or B. The AA grade panels are always preferable,
however, AB grade is acceptable. All plywood should be a minimum of three
plies. All fastenings should be bronze or hot dipped galvanized ferrous metal.
Brass fastenings are not advised nor are electroplated screws commonly sold in
hardware stores. All screws are to be of the flat head type intended for wood.
All nails are of the ring type nail common to boat construction. Unless
otherwise specified, all wood-to-wood joints are to be glued with a waterproof
or highly water resistant glue such as plastic resin, epoxy or equivalent type
used per the manufacturer's instructions regarding temperature, clamping
requirements, curing time, and mixing method.
Abbreviations: DF = Douglas-fir, SP = Sitka spruce, MAH = Mahogany.
ITEM |
MATERIAL |
NO. PCs. |
SIZE |
LUMBER: |
Framework - Frames #1 & #2 |
SP or Mahog |
1 |
1" x 4" x 7' |
Framework - Bow Piece |
SP or Mahog |
1 |
1" x 3" x 4' |
Sheers #4 & #5 |
Mahog |
2 |
1" x 8" x 8' |
Midship seat for #1 |
Mahog |
1 |
1" x 3" x 4' |
Midship seat for #2 |
Mahog |
1 |
1" x 5" x 4' |
Skeg |
SP or Mahog |
1 |
1" x 3" x 2' |
Aft seat #6 |
Mahog |
1 |
1" x 8" x 4' |
Bow seat #9 |
Mahog |
1 |
1" x 8" x 3' |
*Mast brace #13 |
Mahog |
1 |
1" x 6" x 4' |
*Daggerboard |
Mahog |
1 |
1" x 8" x 3' |
*Rudder #11 |
Mahog |
1 |
1" x 8" x 3' |
PLYWOOD: |
Bow member #3 & center frames #1 & #2 |
Ext PW-AB |
1 |
1/4" x 4' x 4' |
Transom #0 |
Ext PW-AB |
1 |
3/4" x 2' x 4' |
Bottom planking |
Ext PW-AB |
1 |
1/4" x 4' x 8' |
Side planking |
Ext PW-AB |
1 |
1/4" x 4' x 8' |
*Not required for non-sailing dinghy |
FASTENINGS: Nails refers to ring type boat nails in bronze. Screws
refers to flat head wood type in hot tipped galvanized or silicon bronze.
- 3/4" #8 Nails - 1/2 lb.
- 1" #8 Screws - 18 dozen
- 1-1/2" #8 Screws -7 dozen
GLUE: Epoxy - 1 quart |
Return
|