L Gato Bill of Materials

The following list of materials is intended to be a general guide only. Before ordering any materials, the text and plans should be checked for possible options. All lumber listed as 1" stock is to be standard "lumberyard four-quarter" material which when finished may vary to somewhat less or slightly more than 3/4" in thickness. All widths are NET and all lengths allow for cutting to fit. Grouping lumber and purchasing random-random material to resaw to the required size will result in considerable savings. All lumber used should be first grade free from shakes and knots. Although spruce (Sitka variety) and mahogany (dark red Philippine type) are called out in the listing, lumber typical to the locale and of similar types and weights may be substituted. All plywood (PW) is to be marine (MAR) or exterior (EXT) grade. The marine-type is preferable as the inner cores are solid and thus the panel has more structural integrity. Douglas-fir (DF) is satisfactory with the quality of the exposed faces of the veneer being designated by the letters "A" or "B". The "AA" grade panels are always preferable, however, "AB" grade is acceptable. All plywood should be a minimum of three plies. All fastenings should be bronze or hot dipped galvanized ferrous metal. Brass fastenings are not advised nor are the electroplated screws commonly sold in hardware stores. All screws are to be of the flat head type intended for wood. All nails are of the ring-type nail common to boat construction. Unless otherwise specified, all wood-to-wood joints are to be glued with a waterproof or highly water resistant glue such as plastic resin, resorcinol, epoxy, or other equivalent type used per the manufacturer's instructions regarding temperature, clamping requirements, curing time, and mixing method.
ABBREVIATIONS: Sitka spruce=SP, Douglas-fir=DF, Mahogany=Mahog, Plywood=PW, Marine plywood=MAR

ITEM MATERIAL NO. PCs. SIZE
LUMBER:
*Bulkhead, transom
& dagger-board
trunk frames
SP or Mahog 2 1" x 8" x 9'-6"
*Bulkhead top cleat Mahog 1 1-1/4" x 1-1/2" x 12'
Sheer and ribbands SP or Mahog 12 1" x 1" x 12'
Keel laminations SP or Mahog 4 1" x 3" x 11'
*Cockpit tray, sides SP or Mahog 2 1" x 4" x 4'-6"
*Cockpit tray
splash shield
SP or Mahog 1 1/2" or 1" x 8" x 8'
*Cockpit tray back SP or Mahog 1 1" x 4" x 8'
Cockpit tray
side cleats
SP or Mahog 2 1" x 1-1/2" x 4'
Cockpit tray
back cleat
SP or Mahog 1 1" x 3-1/2" x 8'
Cockpit tray
splash shield cleat
SP or Mahog 1 1" x 1-3/4" x 8'
Cockpit tray
center batten
SP or Mahog 1 1" x 2" x 6'
*Mast support
beam upright
SP or Mahog 1 1" x 6" x 8'
Mast support
beam base
SP or Mahog 1 1" x 4" x 8'
Mast support
beam top
SP or Mahog 1 1/2" x 4" x 8'
*Daggerboards Mahog 1 1" x 12" x 8'
Misc. blocking SP or Mahog As required
PLYWOOD:
Planking DF PW MAR AA 2 3/16" or 1/4" x 4'x12'
(or 3 sheets 4'x8')
Decking DF PW EXT AB 2 3/16" or 1/4" x 4'x8'
Cockpit tray, bottom DF PW EXT AB 1 3/8" x 4' x 6'
*Rudder & stem
laminations
DF PW EXT AB 1 1/2" x 4' x 4'
*Bulkheads, transom
& daggerboard
trunk sides
DF PW EXT AB 1 1/4" x 4' x 8'
* These items are not required when purchasing a Frame Kit.
FASTENINGS:
  • SCREWS: Flat head wood type, bronze or hot dipped galvanized iron.
  • 1" #8 Screws - 5 gross
  • 1-1/2" #8 Screws - 5 gross
  • NAILS: Ring type, Bronze or Monel
  • 1" #12= 5 pounds
  • CARRIAGE BOLTS: Bronze or hot dipped galvanized
  • 1/4" x 4-1/2" - 2 required
  • 1/4" x 5" - 2 required

GLUE: Epoxy - Approximately 1/2 gallon


Return