Glen-L 30PW Bill of Materials
The following list of materials is intended to be a general guide only.
Before ordering any materials, the text and plans should be checked for
possible options. All lumber listed as 1" stock is to be standard
"lumberyard four-quarter" material which when finished may vary to
somewhat less or slightly more than 3/4" in thickness. All widths are NET
and all lengths allow for cutting to fit. Grouping lumber and purchasing
random-random material to resaw to the required size will result in
considerable savings. All lumber used should be first grade free from shakes
and knots. Although spruce (Sitka variety) and mahogany (dark red Philippine
type) are called out in the listing, lumber typical to the locale and of
similar types and weights may be substituted. All plywood (PW) is to be marine
(MAR) or exterior (EXT) grade. The marine-type is preferable as the inner cores
are solid and thus the panel has more structural integrity. Douglas-fir (DF) is
satisfactory with the quality of the exposed faces of the veneer being
designated by the letters "A" or "B". The "AA"
grade panels are always preferable, however, "AB" grade is
acceptable. All plywood should be a minimum of three plies. All fastenings
should be bronze or hot dipped galvanized ferrous metal. Brass fastenings are
not advised nor are the electroplated screws commonly sold in hardware stores.
All screws are to be of the flat head type intended for wood. All nails are of
the ring-type nail common to boat construction. Unless otherwise specified, all
wood-to-wood joints are to be glued with a waterproof or highly water resistant
glue such as plastic resin, resorcinol, epoxy, or other equivalent type used
per the manufacturer's instructions regarding temperature, clamping
requirements, curing time, and mixing method.
ABBREVIATIONS: Douglas-fir=DF, Mahogany=mahog, Plywood=PW, Marine
plywood=MAR
ITEM |
MATERIAL |
NO. PCs. |
SIZE |
LUMBER: |
Bulkhead & transom
frame members |
Oak or mahog |
235 bd. ft. random-random material with widths to 10" or
more, 1-1/4" stock. |
Floor timbers & stem |
Oak, mahog or DF |
75 bd. ft. random-random material with some widths to 12",
2" stock. |
Keel |
Oak or mahog |
2 |
1-1/4" x 8" x 26' |
Chine logs |
Oak or mahog |
2 |
1-1/4" x 3" x 29' |
Sheer clamps |
Oak or mahog |
2 |
1-1/4" x 3" x 32' |
Raised sheer clamps |
Oak or mahog |
2 |
1-1/4" x 2" x 24' |
Bottom planking battens |
Oak or mahog |
8 |
1-1/4" x 2" x 28' |
Side planking battens |
Oak or mahog |
8 |
1-1/4" x 2" x 31' |
Carlings |
Oak or mahog |
2 |
1-1/4" x 2" x 21' |
Decking strongback |
Oak or mahog |
1 |
1-1/4" x 4" x 6' |
Decking battens |
Oak or mahog |
2
2
2 |
1-1/4" x 2" x 20'
1-1/4" x 2" x 6'
1-1/4" x 2" x 7' |
Seat back/side
deck carling |
Oak or mahog |
2 |
1-1/4" x 2" x 7' |
Cabin clamp |
Oak or mahog |
2 |
1-1/4" x 2" x 18' |
Cabin top strongback |
Oak or mahog |
1 |
1-1/4" x 6" x 15' |
Cabin top battens |
Oak or mahog |
4 |
1-1/4" x 2" x 17' |
Cabin side |
Oak or mahog |
2 |
1" x 7" x 18' |
Cabin front |
Oak or mahog |
1 |
1-1/4" x 6" x 3' |
Cockpit coaming |
Oak or mahog |
2 |
1" x 6" x 7' |
Hatch beams |
Oak or mahog |
2
1 |
1-1/4" x 3" x 4'-6"
1-1/4" x 4" x 2'-6" |
Motor stringers |
Oak, mahog or DF |
2 |
2" x 6" x 7'-6". |
Motor stringer blocking |
Oak, mahog or DF |
1 |
2" x 2" x 7' |
Cockpit sole beams |
Oak or mahog |
2 |
1-1/4" x 4" x 5' |
Misc. hull cleats |
Oak or mahog |
200 lineal feet, 1" x 2" stock |
Sheer rub rail |
Oak, mahog or teak |
2 |
1-1/4" x 2" x 32' |
Keel appendage
(1st lamination) |
Oak, mahog or DF |
1
1 |
1-1/4" x 7" x 20' OR
2" x 8" x 20' |
Keel appendage
laminations |
Oak, mahog or DF |
360 lineal ft 1-1/4"x5" stock, (12' min
lengths)
OR 276 lineal ft, 2" x 6" stock,(12' min lengths
each) |
Keel appendage
heel piece |
Oak, mahog or DF |
1 |
3" x 8" x 4' (or laminate as rqd) |
PLYWOOD: |
Transom |
DF AB Ext |
1 |
3/4" x 4' x 8' |
Stem laminations
& breasthooks |
DF AC Ext |
1 |
3/4" x 4' x 8' |
Bulkheads |
DF AB Ext |
8
4
OR 14 Total |
1/2" x 4' x 10'
1/2" x 4' x 8'
1/2" x 4' x 8' |
Side & bottom planking |
DF AA or AB MAR |
50 |
1/4" x 4' x 8' |
Raised sheer side
planking |
DF AB Ext |
2 |
3/8" x 4' x 8' |
Decking, forward |
DF AB Ext |
2 |
1/2" x 4' x 8' |
Decking, side |
DF AB Ext |
3 |
1/2" x 4' x 8' |
Cabin top |
DF AB Ext |
2
2
OR 5 Total |
1/2" x 4' x 8'
1/2" x 4' x 10'
1/2" x 4' x 8' |
FASTENINGS:
- SCREWS: Flat head wood type, bronze or hot dipped
galvanized iron.
- 1" #8 Screws - 5 gross
- 1-1/4" #8 Screws - 8 gross
- 1-1/2" #8 Screws - 3 gross
- 2" #10 Screws - 11 gross
- 3" #14 Screws - 1 gross
- NAILS: Ring type, Bronze or Monel
- 1" #12= 9 pounds
- 1-1/4" #12 - 13 pounds
|
Return
|